usage_summary
Differences
This shows you the differences between two versions of the page.
| — |
usage_summary [2023/07/21 09:33] (current) badmin created |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| + | == Usage summary == | ||
| + | |||
| + | This is just a copy of the output of binvox when run without parameters: | ||
| + | |||
| + | <code> | ||
| + | --- [binvox] mesh voxelizer, version 1.35, build #881 on 2023/04/18 16:03:29, running on Linux | ||
| + | --- written by Patrick Min, 2004-2023 | ||
| + | |||
| + | Error: missing model filename | ||
| + | |||
| + | Usage: binvox [-d <voxel dimension>] [-t <voxel file type>] [-c] [-v] <model filespec> | ||
| + | -license: show software license | ||
| + | -d: specify voxel grid size (default 256, max 4096) | ||
| + | -t: specify voxel file type (default binvox, also supported: hips, mira, vtk, raw, schematic, msh, nrrd) | ||
| + | -c: z-buffer based carving method only | ||
| + | -dc: dilated carving, stop carving 1 voxel before intersection | ||
| + | -v: z-buffer based parity voting method only (default is both -c and -v) | ||
| + | -e: exact voxelization (any voxel intersecting a convex polygon gets set)(does not use graphics card) | ||
| + | Additional parameters: | ||
| + | -bb <minx> <miny> <minz> <maxx> <maxy> <maxz>: force a different input model bounding box | ||
| + | -ri: remove internal voxels | ||
| + | -cb: center model inside unit cube | ||
| + | -rotx: rotate object 90 degrees ccw around x-axis before voxelizing | ||
| + | -rotz: rotate object 90 degrees cw around z-axis before voxelizing | ||
| + | both -rotx and -rotz can be used multiple times | ||
| + | -nf <value>: use normalization factor <value> (default 1.0) | ||
| + | -aw: _also_ render the model in wireframe (helps with thin parts) | ||
| + | -fit: only write the voxels in the voxel bounding box | ||
| + | -bi <id>: when converting to schematic, use block ID <id> | ||
| + | -mb: when converting using -e from .obj to schematic, parse block ID from material spec 'usemtl blockid_<id>' (ids 1-255 only) | ||
| + | -os <slice index>: voxelize a single slice a index <slice index> | ||
| + | -pb: use offscreen pbuffer instead of onscreen window | ||
| + | -down: downsample voxels by a factor of 2 in each dimension (can be used multiple times) | ||
| + | -dmin <nr>: when downsampling, destination voxel is on if >= <nr> source voxels are (default 4) | ||
| + | Supported 3D model file formats: | ||
| + | VRML V2.0: almost fully supported | ||
| + | UG, OBJ, OFF, DXF, XGL, POV, BREP, PLY, JOT: only polygons supported | ||
| + | Example: | ||
| + | binvox -c -d 200 -t mira plane.wrl | ||
| + | </code> | ||
usage_summary.txt ยท Last modified: 2023/07/21 09:33 by badmin
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 4.0 International
